US69910A - gates - Google Patents

Description

@niet was @anni ffii.

rnrsovnn vkimintr-Brr.

iiilgc tlgrbuh rifarsi in in tips; attcts iatcnt mit mating putt nf tige sinne.

To ALL WHoM I'r MAY eoNeEnN.

Beit known that I, JOSEPH IQGTES, of Lincoln, Logan county, Stateof Illinois, have invented an Improved Bridle-Bit; and I do hereby .declare the following to be an exact description thereof, reference being had to theaceompanying drawings, and to the letters oi' reference marked thereon, making a part of-this speciiicaticn, in which- Figure 1 represents a sido elevation ofthe bit.

`Figure 2, a fro'nt view.

Figure 3, anrinside view ofthe disk;

Figure 4, a view ofthe opposite disk,- showing the construction and location of the spring on the inside.

Figure 5, an end view of bit-bar.

A is the bit-bar or moutl1-pioce,"that is rounding at top, flat on one side, and tapers te the bottom, and has a concavity near the centre on its lower edge. B Bare two disks, the outer disk being part of the bit forming the lever-disk, having a round mortise, C, in which the round ends of the bit-bar A fit and revolve. The inner or cheek disk B is round, having a ring, D, at top, to` which the headstall and curb-chain are attached, and a halt` ring, E, to which 'a check-rein is to be attached. The centre ofthis inner disk B has a square mortise, G, in which the square tenen on the .end of bit-bar is permanently fitted. vII II are spring shuttle-keys, working in recesses between the cheek and lever disks B, and the shuttle-keys are adjusted or raised in their recesses by means of the studs J'operating in their slots K. L is the movable stay-rod, that is fastened at the lower ends of the bit by passing through the levers of the bit and held by -pins M. N, the circular recess, with stop recesses, so `tluit the shuttle-key may pass around and fall into the several stop-recesses, to give the bit any required angle of less or greater leverage.. P is the full lever-stop recess. `q, half-lever stopvrecess. l, anti-leverstop recess.` AS, thehitch-stop recess. 1, thc ring to receive the rein. UV is a spring fitted into the inner side of lever-disk B, and operating in a groove of the disk, and isattached to the shuttle-key for the purpose of forcing the shuttle-key H into the several stop recesses when required to change the angle ofthe bit. 'Ihe bitbar A is fastened to the disksB by screw-nuts V on the outside. I intend to cover the rilns of the disks B with a iiange, if necessary, so as to prevent the horses slbbers from passing between the disks,

The advantages of this bridle bit with double disks, are its movable and adjustable principle, regulated by the devices, that make the bit easy on the horses mouth, and when required is suiciently severe te control the horse with perfect ease, the round orilat side of the bit-bar being brought to bear upon the tongue and under jaw of the horse at the will of the rider by merely changing the angle and leverage of the bit to suit a soft or hard-mouthed horse; the leverage of the bit being easily regulated, whenever required, by raising the studs J and turning the inner disk B until the shuttle-keysH fall into tho stop recess to secure the proper angle and leverage required. VThe bit is likewise easily adjusted so aste allowthe horse to drink freely where the water is shallow.

Another important advantage of this bit is that it prevents the` horse from tearing his bridle and escaping from the hitching-post, by merely turning the stay-rod L around over his muzzle until the levers pass the point at right angles with the line of the head of the horse, when they will be held at that angle by the shuttle-keys H springing into the stop recesses S. Thelcvers in this position are at right angles with the line of the bar and curb-chain, as also with the bit-bar and-the point to which he is hitched. As the horse pulls upon the reins the tendency is to bring the'reins T on the endsof the levers, and the rings D ou the inner disks B, on a true` line with the line of draughtibetween the head of the horse and the point at which he ishitehed, which tendency is resisted and counteracted bythe curb-chain pressing on the under side of and the bit-bar on the upperside of the jaw of vthe horse. vThe severe pain caused by the sharp antagonism, caused by the pulling of the `horse, compels him to cease pulling and remain quiet with vslack reins. A horse is thus prevented from escaping by tearing or slipping his bridle-the tricks of many horses. f l What I claim as my invention, and desire to secure by Letters Patent, isr-` 1. .The shape and construction lof the bit-bar A, as herein described, and for the purposes set forth.

2. The double cheek disks B B,constructed with the shuttle-keys H, studs J, circular recess N, and stop recesses I Q R S, when arranged, combined, and operated as herein described, and for the purposes set forth,

' Jo. P. GATES..

Witnesses z J. FRANKLIN REIGART. EDM. F. BROWN.

Images